What are the two types of current transformers?

Aug 29, 2025 Leave a message

Analysis of the Two Main Types of Current Transformers​

Current transformers are core devices for current measurement and protection in power systems and they are mainly divided into two types which are electromagnetic current transformers and electronic current transformers based on structural form and installation method. These two types have significant differences in operating principles performance characteristics and applicable scenarios with details as follows:​

 

I. Electromagnetic Current Transformer (ECT)​

1. Operating Principle​

ECT is designed based on the principle of electromagnetic induction and consists of an iron core a primary winding and a secondary winding. The primary winding is connected in series with the measured power line and the current passing through the line generates an alternating magnetic field which passes through the iron core to induce a low-amplitude current in the secondary winding (usually with a secondary rated current of 5A or 1A). The secondary winding is connected to measuring instruments (such as ammeters) or protection devices to realize indirect measurement and monitoring of the high current on the primary side.​

 

2. Core Features​

ECT has a mature structure that adopts a traditional electromagnetic induction structure with low technical threshold and stable production process and it has been used in power systems for more than a century with high reliability (failure rate usually below 0.1%). It has a limited measurement range and due to the magnetic saturation characteristics of the iron core it can only maintain high measurement accuracy within 1.2-1.5 times the rated current and exceeding the rated current easily causes magnetic saturation leading to secondary current distortion. It has iron loss and copper loss where the iron core produces hysteresis loss and eddy current loss and the winding has resistance loss which generates a certain amount of heat during long-term operation requiring heat dissipation design (such as natural ventilation heat sinks) to be considered. It has high insulation requirements as the primary side is in direct contact with high-voltage lines (such as 110kV 220kV power grids) and oil-paper insulation SF₆ gas insulation or solid insulation materials must be used to ensure electrical isolation between the primary side and the secondary side (low-voltage side).​

NEW DP Current Transformers

3. Applicable Scenarios​

ECT is widely used in medium-low voltage to high-voltage power systems especially suitable for traditional substations industrial distribution systems low-voltage distribution circuits and other scenarios with typical applications including current measurement and relay protection (such as overcurrent protection differential protection) in 10kV-500kV substations current monitoring in low-voltage distribution circuits of industrial plants (such as 380V motor circuits) and supporting energy metering in residential distribution rooms (used with energy meters).​

II. Electronic Current Transformer (ECT)​

1. Operating Principle​

Electronic current transformer abandons the traditional electromagnetic induction structure and realizes current measurement based on the "Hall Effect" "Magneto-Optical Effect" or "Rogowski Coil" principles. The Hall Effect type utilizes the characteristic that the Hall voltage generated by a Hall element in a magnetic field is proportional to the measured current to directly convert the current signal into a voltage signal which is output as a digital or analog quantity through a signal processing unit. The Magneto-Optical Effect type (Optical Current Transformer) transmits laser through optical fiber and when the laser passes through the magneto-optical material in the magnetic field of the measured current its polarization state changes where the amount of polarization state change is related to the current magnitude and then the current signal is restored through a photoelectric conversion unit. The Rogowski Coil type uses an air-core coil (without an iron core) and the magnetic field generated by the measured current induces a voltage signal proportional to the current change rate in the coil which is restored to a signal proportional to the current through an integrating circuit.​

NEW DP Current Transformers

2. Core Features​

Electronic current transformer has a wide measurement range and without the problem of iron core magnetic saturation it can measure the range of 0.1-20 times the rated current especially suitable for quickly capturing short-circuit currents (thousands to tens of thousands of amperes) to meet the fault protection needs of power systems. It has no iron loss and copper loss where the Hall type and Rogowski Coil type have no iron core and the magneto-optical type has no winding resulting in almost no loss during operation and extremely low heat generation without the need for complex heat dissipation design. It realizes signal digitalization that can directly output digital signals (such as IEC 61850 standard digital quantities) to adapt to the digital communication needs of smart substations and reduce interference and attenuation during analog signal transmission. It has small size and light weight and compared with electromagnetic transformers of the same voltage level its volume can be reduced by more than 50% and its weight can be reduced by more than 60% which is convenient for installation in narrow spaces (such as inside GIS switchgear).​

 

3. Applicable Scenarios​

Electronic current transformer is mainly used in high-voltage ultra-high-voltage smart grids and scenarios with high requirements for measurement accuracy and digitalization with typical applications including digital protection and monitoring of 220kV and above smart substations (such as ultra-high-voltage DC transmission systems) grid-connected current monitoring of new energy power stations (wind power photovoltaic power stations) (adapting to the fluctuating current measurement of new energy power generation) current measurement inside GIS (gas-insulated switchgear) (utilizing its advantages of small size and high voltage resistance) and traction power supply systems for rail transit (adapting to the large fluctuation characteristics of traction current).

Send Inquiry

whatsapp

Phone

E-mail

Inquiry